English [Español]
United States [Change]
Products > Climbing-Equipment > Extension Ladders > D7100-2LV Series > D7140-2LV 40 ft Type IA Fiberglass D-Rung Leveling Extension Ladder > D7140-2LV

Product Image
D7140-2LVD7140-2LVD7140-2LVD7140-2LVD7140-2LVD7140-2LV

Resources

  •  
  •  
  •  View D7100-2LV Series Page
  •  
  •  Series Comparison
  •  Replacement Parts
  • Share
  •  Email page | Print this page

Accessories

Complementary Products

You May Also Consider

D7140-2LV 40 ft Type IA Fiberglass D-Rung Leveling Extension Ladder


Performance Overview

SizeStyleApprox. Closed LengthReach HeightLoad CapacityPerformance Rating
40 ftMulti Section20 ft37 ft300 lbs

The D7140-2LV extension ladder boasts a duty rating of 300 pounds and has factory-installed LeveLok® levelers to enable the ladder to adapt to uneven terrain. With simple foot action, each leveler can extend up to 10 inches in 3/16 inch increments. This ladder is ideal for utility or telecommunication industries. The external guides at the top of the base section secure the interlocking rails. The top of the fly section has pre-pierced holes for easy installation of accessories. The base and fly sections easily separate to use the base section as a single ladder. Fiberglass rails are non-conductive for working near electricity.




Features

  • Factory installed LeveLok® Leveler enables ladder to adapt to uneven terrain
  • With simple foot action, Leveler extends up to 10 inches in 3/16 in increments
  • Exclusive ALFLO® rung joint means TWIST-PROOF® performance
  • 1-1/4 in slip-resistant TRACTION-TRED® D-rungs
  • Plate and rung assembly are riveted at four points to each side rail to allow for rung replacement
  • Interlocking Side Rails with nylon coated internal rail guides on bottom of fly section increase ease of operation
  • External guides at top of base section securely interlock rails
  • Rugged gravity spring locks operate smoothly
  • Rugged, heavy duty extruded rung locks are spring loaded to operate smoothly
  • Pre-pierced holes for easy field installation of accessories
  • Dual action feet with slip-resistant pad and spur plate for use on hard or penetrable surfaces
  • Mar-resistant molded end caps
  • Ideal for utility and telecommunication industries
  • LeveLok® is a registered trademark of the LeveLok Corporation.


Specifications

FeatureSize / Details
Size40 ft
Max. Safe Working Height35 ft
Max. Open Extended Length35 ft
StyleMulti Section
Load Capacity300 lbs
MaterialFiberglass
Rung TypeD-Rung
Foot MaterialSlip-resistant pad
Number of Sections2
Base Width22 in outside rails, 25-3/4 in outside shoes
CertificationsANSI A14.5 (2007); OSHA
Approx. Closed Length20 ft
Reach Height37 ft
Approx. Shipping Weight Lbs.134.5
Approx. Cu. Ft. Per Unit22.5
Performance Rating




Package Contents

Part NumberQtyDescription

Dimensions

FeatureSize
Rails Dimension4 in
Flange Dimension1-3/4 in
Rung Dimension1-3/4 in
Fly Width16-3/4 in


Additional D7100-2LV Series Models

Model No.SizeMax. Safe Working HeightMax. Open Extended LengthLoad CapacityBase WidthApprox. Closed LengthBuy Online
D7120-2LV20 ft17 ft17 ft375 lbs19 in outside rails, 22-3/4 in outside shoes10 ft
D7124-2LV24 ft21 ft21 ft375 lbs19 in outside rails, 22-3/4 in outside shoes12 ft
D7128-2LV28 ft25 ft25 ft375 lbs19 in outside rails, 22-3/4 in outside shoes14 ft
D7132-2LV32 ft29 ft29 ft375 lbs19 in outside rails, 22-3/4 in outside shoes16 ft
D7136-2LV36 ft32 ft32 ft300 lbs22 in outside rails, 25-3/4 in outside shoes18 ft
D7140-2LV40 ft35 ft35 ft300 lbs22 in outside rails, 25-3/4 in outside shoes20 ft


Please provide the height, width and depth of the ladder when collapsed.

Ladder will need fit [slide] into a storage "box".
Asked by: TCS
The height of the ladder collapsed ladder is 246 1/2". The width is 26 15/16". The thickness will be 8".
Answered by: Werner Customer Care
Date published: 2016-03-26

D7136-2LV with the PK80-2 Automatic Leveler Kit

I was unable to find information to determine which Leveling Kit is factory installed on the D7136-2LV Ladder. I am interested in the PK80-2 Automatic Leveler Kit. I have read a similar posted question regarding the 32' model which turned out to be model number D7132-2X0004. If i want to order the D7136-2LV ladder with Automatic Leveling Kit PK80-2 , what is the Model Number? Best Regards, Garrett
Asked by: Garrett
The levelers that come installed on the D7136-2LV is the PK70-1. If you want the PK80-2 levelers installed on the D7100-2 series of ladder you would need the D7140-2x0004 or the D7132-2x0004. We currently do not have an active model for the D7136-2 with the PK80-2 factory installed.
Answered by: Werner Customer Care
Date published: 2015-06-08

can you use this ladder when seperated?

Asked by: bob
The D7140-2LV ladder may be separated to use the base section only as a single ladder. The fly section does not have the proper footing to be used as a single ladder.
Answered by: Werner Customer Care
Date published: 2014-01-03

If the rope and pulley system is broken on the ladder, should the ladder be taken out of service until it is replaced?

Asked by: Dylan
A ladder should not be used with any broken or missing pieces. The rope and pulley are needed for safely raising the ladder to the desired height before climbing. Please refer to the ladder inspection form for a detailed parts inspection breakdown.
Answered by: Werner Customer Care
Date published: 2014-03-28

The rating decal on the rail of the ladder is not visible. Can I get a replacement decal.

Asked by: Jack
Werner Co. does offer replacement safety label kits and duty rating label kits. These kits may be special ordered through your local distributors. Please provide the distributor with your model number and they can special order the correct kits for your unit.
Answered by: Werner Customer Care
Date published: 2014-01-02

If the rope and pulley system is damaged, does it need to be sent in to Werner for repair or can it be repaired in the field?

Asked by: Dylan
The Werner Co does not offer a repair service for ladders. However, replacement parts are made available to do a field repair of the ladder. The rope and pulley are both available as replacement parts. Please visit our website at www.buywerneronline.com to order your parts online.
Answered by: Werner Customer Care
Date published: 2014-06-22

Can additional Pins be purchased for the leveling legs

Asked by: Crystalfred
Please visit our website at www.buywerneronline.com to order your desired replacement parts online. Please have your model number and MK/MARK number available off of your ladder at the time to order replacement parts.
Answered by: Werner Customer Care
Date published: 2014-01-02

Can this ladder be ordered with V rung and cable hooks?

Asked by: JB
The Cable Hook and V-Rung kit is available as an additional accessory to be added to this ladder. The correct kit number is 92-89 for D7100-2LV series ladders.
Answered by: Werner Customer Care
Date published: 2014-06-09

made in USA

is this made in KY or MX?
Asked by: Anonymous
The D7100 seriers ladders are manufactured in Mexico. In recent years Werner Co. has expanded globally to become the world leader in the manufacturing and distribution of ladders, climbing equipment and ladder accessories. Werner is now available in new markets and product categories and has added manufacturing and distribution facilities in the U.S. and around the world to satisfy global demand.
Answered by: Werner Customer Care
Date published: 2014-12-27

What is the weight of an Extra Heavy duty 36 foot extension ladder

Asked by: TL
The model D7136-2LV ladder weighs 121lbs.
Answered by: Werner Customer Care
Date published: 2017-07-23
  • y_2017, m_9, d_21, h_22CST
  • bvseo_bulk, prod_bvqa, vn_bulk_2.0.3
  • cp_1, bvpage1
  • co_hasquestionsanswers, tq_17
  • loc_en_US, sid_D7140-2LV, prod, sort_[SortEntry(order=LOCALE, direction=DESCENDING), SortEntry(order=FEATURED, direction=DESCENDING), SortEntry(order=NUM_ANSWERS, direction=DESCENDING)]
  • clientName_werner



Different types of ladders are designed to keep you safe and productive when climbing or standing. Using the wrong style of ladder or simply ignoring the limitations of climbing equipment can result in a fall or serious injury.
Height is referring to the actual ladder height. Extension ladders should be 7 to 10 feet longer than the highest support or contact point, which may be the wall or roof line. The highest standing level is four rungs down from the top. The highest permitted standing level on a stepladder is two steps down from the top.

Reach height is the maximum reach assuming a 5’6” person with a vertical 12” reach.
Ladders are designed to safely hold up to a specific amount of weight. The Werner Performance System defines five different capacities using a color and star rating system. The Duty Rating is defined as the maximum safe load capacity of the ladder. A person’s fully clothed weight plus the weight of any tools and materials that are carried onto the ladder must be less than the load capacity.

Werner offers ladder made from fiberglass and aluminum. Each material has characteristics which make it best for certain applications, or one material may simply fit the personal preferences of the user. For example, if working around electricity users should select fiberglass products due to their non-conductive side rails.